https://www.convergent-design.com/suppo ... loads.html
neue FW fürn 7Q ist seit letzter Woche online...
Hauttöne für die FS700 in slog2 sind drastisch verbessert und LUT-Support!
neue Features:
Expanded Odyssey LUT System, including custom 3D-LUTs
Improved & Expanded set of Preset LUTs
Support for user-loadable custom 3D-LUTs (up to 140, Odyssey7Q, Odyssey7Q+)
.CUBE Luts translated for Odyssey using CD 3D-LUT Converter App
LUTs are currently for MONITORING only, not “baked in”
LUTs viewed during recording noted in XML file metadata
(new CD Apple ProRes Transfer Utility 1.7 required)
Extended and Legal Range LUTs Supported (EE vs LL)
LUT Routing to Tools & Outputs
Image Analysis Tools can measure “LUTTED” image or original source
Video outputs can independently turn ON/OFF LUT or Mirror OLED
Anamorphic DeSqueeze
2.0x, 1.5x, 1.33x Support
Corrected image sent to video outputs, recording unaffected
4K / 2K Monitoring Modes (Odyssey7Q, Odyssey7Q+)
17:9 Letterboxed within 16:9 image or Center-Cut to 16:9
Letterbox or Center-Cut image sent to video outputs, full frame recorded.
Monochrome Monitoring Mode
View Luma only or individual Red, Green, or Blue channel in grey tone
Dual Zebras
Set high & low for each, can overlap, separately selectable colors
Expanded False Color Mode
Added Pink for Six colors
Each color set high & low, can overlap
Expanded OLED Controls
Advanced Monitor Calibration Controls
Color channel bias controls, SMPTE color bars reference
Improved Multi-Stream Mode Switching
Switch between inputs without image flicker or glitch.
Safe Eject at power down
Automatically closes all file directories on shut down
Improved Sony FS RAW color reproduction
Improved image quality in CinemaDNG and Apple ProRes recording
FS700 Apple ProRes recording with S-Log2 or REC709(800%)
FS7 CinemaDNG & Apple ProRes require SGamut3.Cine Color Space
FIXES & IMPROVEMENTS
FIXED AUD OUT (Headphones) unmute\
FIXED Audio gain settings when switching Analog to SDI
FIXED Safe Eject process to remove OLED flashing during procedure
FIXED FS700 4K RAW -> HD Apple ProRes detection
IMPROVED 4K Apple ProRes playback
IMPROVED 4K pixel zoom 1:1 and 2:1
IMPROVED PSF output support in all modes
IMPROVED Reduced overall power usage
IMPROVED Interlaced playback support
IMPROVED 4K -> HD Apple ProRes playback
FIXED hdmi legalize input setting
SOFTWARE UPDATES
CD Apple ProRes Transfer Utility 1.7
LUTs viewed during recording noted in XML file metadata
KNOWN ISSUES
4K HDMI input, to HD HDMI output there are lines in the display. Note HD-SDI output does not have this issue. Recording is unaffected.
When using FS7 / FS700 4K -> 4K Apple ProRes or 4K -> 2K Apple ProRes, enabling color bars with PSF on causes vertical stretching of color bars.
When using color bars, do not power up the unit with a video source connected as this can result in a black screen. Disconnect SDU or HDMI to remedy.
Pixel Zoom in 2:1 does not reach the corners of the image in 16:9 or 17:9
When applying certain LUTs Legal / Extended may need to be selected to match the camera / NLE.
SSD Detection is longer than previous 5-10 seconds.
Loading of SSD LUTS can take up to 30 seconds.
Deletion of Custom LUT Folders not enabled at this time.
Loading of any LUTs go to LUT User folders only.
Image Analysis Tool Overlays are slower than previous firmware (Lines on the display).
When PSF output is selected OLED display is interlaced.
Occasionally when viewing or recording 4K/UHD to 2K/HD SuperSample, lines can appear on the OLED display. Recorded files as unaffected.
IN FS700 4K Raw Burst mode (100p/120p), ten extra frames are recorded at the end of each clip. Occasionally the are bad frames. This will be corrected in future firmware from 450 frames to proper 440 frames.
IN FS700 4K Raw Burst mode (100p/120p) -> 2K/HD Apple ProRes, the amount of frames that are recorded may vary based on trigger type and clip to clip. Note the Odyssey always records 420+ frames in this mode.
Graticules for Image Analysis Tools are not currently displayed on the SDI / HDMI outputs.
Occasionally on startup the firmware version number located under the Safe Eject button will report “2015”. Engage/disengage F1 Screen Lock to reset to display “15.05”.
Deleting luts does not always work reliably, deleted luts can reappear after a power cycle. Workaround: resetting luts via the Odyssey->Reset menu does clear (delete) all custom luts.
Anamorphic Desqueeze is not supported in Canon Half Raw at this time.
1D LUTs are not support, only 3D Luts.